Your name:

Your email address:

* When you see "Choose all that apply", the question may have multiple correct answers and you'll need to get them all.

Exam Questions

You have 60 minutes to answer the questions below.

1, When you install a Bore-Up cylinder you want to make sure:

A.        a longer barrel is installed
B.        a high precision inner barrel is installed
C.        a short barrel is installed
D.       the hopup rubber is replaced
E.        None of the choices.

Answer:

2, Why is it bad for you to lube the barrel too much?

A.        ROF will be slow
B.        accuracy will be affected
C.        battery power consumption will be huge
D.        the inner barrel will break
E.        it isn't bad at all

Answer:

3, Parts with telfon coated finishing are desirable primarily for:

A.        high ROF
B.        very high FPS
C.        very high accuracy
D.        indoor application
E.        outdoor application

Answer:

4, Refer to the exhibit below:

What part is this (hint: this part has a diameter of WAY OVER 1cm) ?

A.        piston head
B.        cylinder head
C.        nozzle
D.        hopup bucking
E.        None of the choices.

Answer:

5,  Refer to the exhibit below which shows a piston head:

Why are the cuttings necessary?

A.        for better air seal
B.        for better accuracy
C.        for durability
D.        for easier adjustment
E.        None of the choices.

Answer:

6, When would double feeding occur?

A. disrupted gear timing
B. under sized cylinder
C. overheated motor
D. burnt fuse
E. None of the choices.

Answer:

7, Which of the following statements are generally true (choose all that apply):

A. Do NOT apply grease on gears.
B. Do NOT apply grease on motor brushes.
C. Do NOT apply silicon oil spray on inner barrel.
D. Do NOT apply silicon oil spray on motor bearing.
E. None of the choices.

Answer:

8, Which of the following AEG models do NOT make use of the “adjustment by lever” type of hopup mechanisms (choose all that apply):

A. TM MP5
B. TM SG552
C. TM G3 SAS
D. CA G36
E. ICS M4

Answer:

9, A fixed hopup mechanism has which of the following problems?

A. flexibility      
B. impact on ROF       
C. impact on FPS      
D. power consumption      
E. cost     

Answer:

10, Which of the following AEG gun models has the shortest inner barrel?

A. FAMAS
B. G3
C. AK
D. P90
E. MP7

Answer:

11, Refer to the exhibit below:

The component shown is used with which of the following mechbox versions?

A. V1
B. V2
C. V3
D. V2 and V3
E. V1 and V2

Answer:

12, Refer to the exhibit below:

The component shown is essential for which of the following purposes?

A. select fire
B. hopup
C. barrel tuning
D. piston adjustment
E. None of the choices.

Answer:

13, Refer to the exhibit below:

Which part is in direct contact with the air nozzle?

A. Part A
B. Part B
C. Part C
D. Part D
E. None of the choices.

Answer:

14, Refer to the exhibit below:

Which part is in direct contact with the bucking?

A. Part A
B. Part B
C. Part C
D. Part D
E. None of the choices.

Answer:

15, Which parts of a EG1000 motor are practically replaceable for performance maintenance?

A. brushes and springs
B. springs and bearing
C. pinion and shell
D. shell and magnet
E. Nothing is replaceable.

Answer:

16, Refer to the exhibit below:

The type of mechbox shown is used by which of the following AEG models?

A. MP5 A4
B. MP5K and SG552
C. G36C and G3
D. AK Warhawk and MP5 RAS
E. M4 and AK74U

Answer:

17, Refer to the exhibit below:

When would you want to disable and bypass the highlighted unit?

A. You are going through a power upgrade
B. You need to use a lower voltage battery
C. You need to replace the motor
D. You need to replace the piston
E. You can NEVER do this

Answer:

18, Refer to the exhibit below:

You may use this component with:

A. TM piston and spring       
B. Systema piston and spring 
C. ICS piston and spring 
D. cylinder head 
E.  hopup bucking 

Answer:

19, Refer to the exhibit below:

You may use this component with:

A. TM spur gear       
B. Systema bushings 
C. ICS tappet plate 
D. cylinder head 
E. piston  

Answer:

20, Refer to the exhibit below:

The kind of hopup mechanism shown is commonly found in which of the following AEG models?

A. M14
B. MP5K
C. SG552
D. M4
E. MP7

Answer:

21, AEG import is allowed in New Zealand under what condition?

A. full auto disabled
B. FPS of no more than 240
C. FPS of no more than 260
D. FPS of no more than 230
E. ROF of 10 shots per second MAX

Answer:

22, An added orange barrel extension glued to the end of the barrel is known as:

A. DOA marking
B. DOJ marking  
C. FDC marking  
D. UN marking 
E. DOC marking 

Answer:

23, What are the limiting factors when deciding the types and classes of BB bullets to use?

A. The amount of pressure available for propelling the BB
B. The strength of the magazine spring
C. Foregrip weight
D. Shape of the pistol grip
E. A and B
F. A and C
G. B and C
H. B and D

Answer:

24, AEG export is allowed in the UK under what condition?

A. full auto disabled
B. FPS of no more than 240
C. FPS of no more than 280
D. FPS of no more than 230
E. None of the choices.

Answer:

25, Normally speaking what FPS can be expected out of a M120 spring?

A. FPS of approx 340
B. FPS of approx 390
C. FPS of approx 480
D. FPS of approx 450
E. None of the choices.

Answer:

26, Refer to the exhibit below:

Which of the following correctly describe a possible benefit of the use of the gear shown?

A. easy setup and configuration
B. high compatibility with motor pinion
C. high compatibility with gear shim sets
D. enhanced ROF
E. None of the choices.

Answer:

27, Which TM AEG model comes with a variable pitch spring as part of the stock configuration?

A. MP5 RAS
B. M4 S System
C. MP7
D. SG552
E. None of the choices.

Answer:

28, Rate this comment: manufacturing of advanced airsoft equipment (such as AEG) is never allowed in Philippine.

A. True
B. False

Answer:

29,  Refer to the exhibit below:

Which gun model uses this motor?

A. MP7
B. Mac 10
C. M93R
D. Scorpion
E. None of the choices.

Answer:

30, Refer to the exhibit below:

What function does the highlighted part provide?

A. nozzle control
B. select fire
C. cut off lever
D. safety control
E. None of the choices.

Answer:
 

31,  Refer to the exhibit below:

Anti reversal goes to:

A. the left most gear
B. the left spur gear
C. the right spur gear
D. the right most gear
E. None of the choices.

Answer:

32, The MP7 AEG is powered by what motor?

A.       Mini 700
B.       Mini 1000
C.       Mini 560
D.       RS 370
E.       RS 540

Answer:

33, Which manufacturer offers bearings suitable for the Marui AEP mechbox?

A. Nineball       
B. Redwolf      
C. ACX      
D. Airsoft Extreme      
E. KJW  

Answer:

34, Refer to the exhibit below:

Which AEG/AEP model uses this kind of piston and cylinder?

A. MP7
B. Mac 10
C. M93R
D. Scorpion
E. None of the choices.

Answer:

35, Joule measurement focuses on:

A. velocity       
B. impact energy      
C. energy consumption      
D. accuracy      
E. None of the choices.  

Answer:

36, 1 ft/s = ?
    
A.       0.3048 m/s
B.       0.348 m/s
C.       3.048 m/s
D.       0.3022 m/s
E.       0.3248 m/s

Answer:

37, Why is WD40 NOT preferable for lubing the slide of your gas blowback hand gun?
    
A.   it may cause damage
B.   it is poison
C.   it is too costly
D.   it dries too quickly
E.   it dries too slow

Answer:

38, Gas leakage usually happens due to:

A.   over-pressured gas system
B.   aging rubber rings
C.   worn-out valves
D.   A and C
E.   A, B and C
F. B and C

Answer:

39, The standard small can gas that comes with most Japanese/Taiwanese gas guns are:

A.   134a
B.   134b
C.   152c
D.   168d
E.   A, B and C
F. B and C

Answer:

40, Refer to the exhibit below:

What function does the kit provide?

A.       a Red Gas adaptor
B.       a Top Gas adaptor
C.       a Green Gas adaptor
D.       a CO2 adaptor
E.       None of the choices.

Answer: